Search found 1415 matches

Go to advanced search

by alan.moore
Tue Jun 15, 2021 6:33 pm
Forum: Four stroke
Topic: Tank panel - dished washers?
Replies: 3
Views: 167

Re: Tank panel - dished washers?

John
The only 'dished washer' I am aware of is the patent number disc that goes under the head of the front screw. Its part 5153-33. Have you had a look on Draganfly site? it shows the panel fixings....

AOMCC single spares did have the patent disc I bought one a few years ago

Cheers
Alan
by alan.moore
Sun Jun 06, 2021 10:42 pm
Forum: Four stroke
Topic: Identification questions
Replies: 14
Views: 257

Re: Identification questions

You'll need civilian footrests if you want rubbers on them... My '39 VH was fitted with WNG footrests with 'non factory' rubbers! Turned out they were ( I think ) Norton pillion footrest rubbers. See this post http://forum.arielownersmcc.co.uk/viewtopic.php?f=48&t=4826 A possible solution if yo...
by alan.moore
Thu Jun 03, 2021 2:04 pm
Forum: Four stroke
Topic: Crankshaft Bearings
Replies: 2
Views: 189

Re: Crankshaft Bearings

I am about to build up the bottom end of my 1956 VB and i note that as well as the roller bearing the crank is supported by two angular contact ball bearings. My question is as they are angular contact then there is supposedly a right and a wrong way round ? Derek You've probably already had a look...
by alan.moore
Tue Jun 01, 2021 11:29 pm
Forum: Four stroke
Topic: Gearbox bush question
Replies: 9
Views: 218

Re: Gearbox bush question

Peter I may have misunderstood your description but the rollers sit in the 'slot' machined in the end of the selector shaft just before the 'gear'. The chamfer on the 'bush' is there to assist in getting the 'roller' loaded selector shaft to enter the bush. D6.jpg Item 39 in the above shows location...
by alan.moore
Mon May 31, 2021 7:11 pm
Forum: Four stroke
Topic: VB chaincase oil leak
Replies: 15
Views: 655

Re: VB chaincase oil leak

Mark
Here's what it should look like

5770-31.jpg
5770-31.jpg (41.59 KiB) Viewed 234 times


I've got one that's been cut off at the end of the threads and the hole in the rear case blocked off. It's a common modification.

Cheers
Alan
by alan.moore
Mon May 31, 2021 2:32 pm
Forum: Four stroke
Topic: VB chaincase oil leak
Replies: 15
Views: 655

Re: VB chaincase oil leak

Mark Here's a pic of the adjusting screw. SDC14403.JPG There is a 'trough' inside the case which collects oil 'flung' off the primary chain. This trough communicates, via a hole in the rear chain case, to the 'trough' in your photo. The tapered end of the adjusting screw alters how much oil comes th...
by alan.moore
Sat May 29, 2021 2:46 pm
Forum: Four stroke
Topic: BA Gearbox hints & tips
Replies: 22
Views: 7008

Re: BA Gearbox hints & tips

John Below is a CP but just the same as BA Fit the selector mechanism in the main case. SDC14398.JPG Remove the 'locating bolt' from the outer case SDC14393.JPG Lower the outer case over the studs. Move the selector splined shaft as required so it fits through the case and the studs line up. Then wi...
by alan.moore
Sat May 29, 2021 1:52 pm
Forum: W/NG General
Topic: W/ng rear stay
Replies: 25
Views: 1448

Re: W/ng rear stay

The centre stay should be vertical from its mounting point up to the guard. The position of the angled rear stay, and therefore the location of its mudguard bracket, is therefore determined by the the location of the centre vertical bracket. The position of mine is verified in that the W/NG carrier...
by alan.moore
Thu May 27, 2021 2:16 pm
Forum: W/NG General
Topic: W/ng rear stay
Replies: 25
Views: 1448

Re: W/ng rear stay

The centre stay should be vertical from its mounting point up to the guard. The position of the angled rear stay, and therefore the location of its mudguard bracket, is therefore determined by the the location of the centre vertical bracket. The position of mine is verified in that the W/NG carrier ...
by alan.moore
Tue May 25, 2021 8:27 pm
Forum: W/NG General
Topic: W/ng rear stay
Replies: 25
Views: 1448

Re: W/ng rear stay

Here are pics from my WNG. First is the rear bracket, second the centre bracket. SDC14386.JPG SDC14387.JPG The 'rivets' are small 6mm stainless coach bolts from Screwfix, with the heads reduced in size and 'flattened' a bit by putting them in the pillar drill and using an angle grinder with a fine g...

Go to advanced search